Skip to main content

Hylas 44 Buyer’s Guide

Bluewater Cruising Sailboat

The Hylas 44 is a centre-cockpit cruising sailboat designed by the renowned German Frers and built by Queen Long Marine in Taiwan (1984–1992). At 22,320 lbs with a 49% ballast ratio, it is well-ballasted and stable offshore. The centre-cockpit layout provides a true aft cabin with guest privacy. Excellent upwind ability — close-winded for a cruiser. Known for strong value on the used market.

Source-checked 25 Oct 2026How we check our guides

H
By Hylas
View all Hylas boats for sale
Type: Bluewater Cruising Sailboat
Size: 44 ft (13.5m)
Since 1985
Share this guide

Updated 10 June 2026 · By Hulls.io Editorial

The Hylas 44: A Complete Guide

The Hylas 44 is a centre-cockpit bluewater cruiser designed by German Frers and built by Queen Long Marine in Kaohsiung, Taiwan. Queen Long’s own timeline dates the 44 to 1984–92 (SAILING magazine, citing the owners’ association, gives US availability from 1985 and production until 1993, when a swim-step transom turned the same hull into the Hylas 45.5). Queen Long commissioned Frers to draw two cruising designs in the early 1980s, which became the Hylas 42 and the 44, and the yard describes itself as founder and owner of the Hylas brand since 1985. In the US the boats were sold largely into Caribbean charter: Bill Stevens of Stevens Charters and then Dick Jachney of Caribbean Yacht Charters (CYC) bought most of them, and CYC became the sole importer of new Hylas yachts in 1990.

German Frers needs little introduction. The Argentine naval architect has drawn racing and cruising yachts for builders including Nautor’s Swan and Hallberg-Rassy. His work on the Hylas 44 reflects the same design philosophy that defines his broader portfolio: a fine, easily driven hull form with moderate proportions, excellent balance, and the kind of understated elegance that ages well. The Hylas 44’s sharp entry, moderate beam, and clean underbody create a boat that John Kretschmer, writing in SAILING, describes as close-winded for a cruising boat — while the 49.4% ballast ratio provides the stiffness and ultimate stability required for serious offshore work.

Queen Long Marine, the Taiwanese builder, was founded in 1978 and remains in operation today; as of 2026 its website lists the H48 and H57 as the current Hylas sailing range. Before the 44 it had built the Stevens 47 (1981) and Peterson 46 (1982). The 44 has a solid hand-laid fibreglass hull with a stiffening network of full-length fore-and-aft stringers and transverse floors, a deck structure of balsa or Airex core bonded with stainless-steel bolts and 3M 5200 sealant, and interior joinery in warm teak and mica that balances the feel of a wooden yacht without the weight and maintenance penalty of an all-timber interior. According to Kretschmer, a former Hylas delivery skipper, several Hylas 44s have completed circumnavigations, including one known passage around Cape Horn.

The centre-cockpit layout is the defining feature of the Hylas 44’s accommodation plan. Unlike aft-cockpit sailboats of similar length, the centre cockpit creates a true aft cabin with a centreline queen berth (on all but the first thirteen hulls) and its own head with shower. Dual walk-throughs connect the main salon to the aft stateroom, with the galley to starboard and the navigation station and aft head to port, the engine beneath the galley console. Kretschmer credits Frers as one of the first designers to use a double walk-through arrangement.

No Hylas 44 listings on Hulls.io right now—selling one? List it from £19.99/month

Hylas 44 Specifications

SpecificationDetail
LOA44 ft 2 in (13.46 m)
LWL34 ft 10 in (10.63 m)
Beam13 ft 6 in (4.11 m)
Draft (fin keel)6 ft 11 in (2.10 m)
Draft (shoal / bulb keel)5 ft 5 in (1.65 m)
Displacement22,320 lbs (10,124 kg)
Ballast (lead)11,020 lbs (4,999 kg)
Ballast ratio49.4%
I (foretriangle height)55 ft 0 in (16.76 m)
J (foretriangle base)17 ft 10 in (5.43 m)
P (mainsail luff)47 ft 0 in (14.33 m)
E (mainsail foot)16 ft 0 in (4.88 m)
Total sail area864 sq ft (80.3 m²)
SA/D ratio17.6
D/L ratio≈235
Capsize screening formula≈1.92
Hull speed7.9 knots
Engines (common)Yanmar 4JH-TE, 55 HP diesel
Engines (early / alternate)Perkins 4-108, 50 HP (early boats) / Westerbeke 62 HP (a few boats)
Fuel capacity80–110 US gal (303–416 litres), sources differ
Water capacity80–100 US gal (303–379 litres)
Hull materialSolid hand-laid GRP (fibreglass)
Deck constructionBalsa / Airex cored GRP, bolted to hull with 3M 5200
Keel typeFin keel with external lead shoe on a fibreglass stub, skeg-hung rudder
RigMasthead sloop (cutter option available)
MastKeel-stepped
Naval architectureGerman Frers
BuilderQueen Long Marine Co., Kaohsiung, Taiwan
US importerDick Jachney (Caribbean Yacht Charters, sole importer from 1990)
Production years1984–1992 (builder’s timeline)

The numbers reveal a thoughtfully balanced offshore cruiser. The displacement of 22,320 lbs gives a displacement/length ratio of about 235, in the moderate band, and Kretschmer notes it is lighter than many comparable cruisers of its day. The ballast ratio of 49.4% is the standout figure — nearly half the boat’s weight is in the lead keel. This is a boat that was engineered, first and foremost, to stay upright in the worst conditions the ocean can produce.

The SA/D ratio of 17.6 sits in the 16–20 band that sailboatdata.com describes as reasonably good performance. The deep fin keel draws 6 ft 11 in (2.10 m) on sailboatdata’s figure (Bluewaterboats.org lists 6 ft 6 in), while the shoal bulb keel at about 5 ft 5 in (1.65 m) opens up the Bahamas, the ICW and other shallow-water cruising grounds.

Two keel configurations were available. The deep-keel version is preferred for open-ocean sailing and windward performance. The shoal-draft bulb keel suits coastal cruising and island hopping. Buyers should understand which option their prospective boat carries, as it affects both sailing characteristics and suitable cruising grounds. Both sloop and cutter rigs are found on the market; the cutter’s inner forestay and staysail give another way to shorten and balance the sail plan in heavy weather.

How Does the Hylas 44 Sail?

Upwind: John Kretschmer, a former head delivery skipper for Hylas who logged around 20,000 bluewater miles in 44s, writes in SAILING that the boat is close-winded for a cruising boat, tracks well, does not pound upwind even in sloppy seas and does not make excessive leeway. The fine entry and deep forefoot are the reason. The trade-off is a wet ride: Bluewaterboats.org notes a steady stream of water sliding over the fine bow and back to the centre cockpit because of the low freeboard, and Kretschmer adds that the small bridgedeck makes a good spray dodger and handy washboards essential in rough weather.

Reaching: The 864 sq ft of total sail area and the SA/D ratio of 17.6 give the Hylas 44 respectable reaching power for a cruiser of its weight. Kretschmer describes the boat as stiff, though it does heel a bit, and with most sail controls led aft it is not a chore to singlehand.

Downwind: Bluewaterboats.org says the 44, with its beam carried well aft, surfs down waves, and Kretschmer recalls surfing at double-digit speeds before the swells from Hurricane Grace. He specifically rejects the online claim that the boat is squirrelly downwind. The large mainsail (with a P measurement of 47 ft and an E of 16 ft) can blanket the headsail dead downwind, so a poled-out headsail or an asymmetric spinnaker is worth having for sustained downwind passages. Cutter-rigged boats can fly a staysail to weather and a poled-out genoa to leeward for trade-wind sailing.

Light air: With an SA/D ratio of 17.6, the boat is adequately but not generously canvassed for light conditions. A larger genoa or a Code 0 on a bowsprit is a worthwhile addition for owners who cruise in light-air regions.

Under power: Engine installations varied across the production run. According to Kretschmer the original engine was the Perkins 4-108 (50 HP), a few boats had Westerbeke 62s, and most came with the Yanmar 4JH-TE, a 55 HP turbocharged four-cylinder diesel that he calls a very good engine that will run a long time. He notes that most boats for sale carry very high engine hours, partly because the engine’s location makes a repower a big job. Fuel capacity is quoted as 80–100 US gallons (Bluewaterboats.org) and as 110 gallons in two stainless-steel tanks (Kretschmer), which he says gives a realistic motoring range of over 500 miles; the hull makes 6-plus knots without pushing the engine much over 2,000 rpm.

Heavy weather: The 49.4% ballast ratio, the Frers hull form and the solid fibreglass construction suit the Hylas 44 to offshore work. Kretschmer sailed 44s through severe weather, including the eye of Hurricane Bob, and says he never felt the hull flex or heard it groan; he adds that it heaves-to efficiently and handles large following seas with ease. The skeg-hung rudder gives the blade some protection, and, as noted above, several Hylas 44s have completed circumnavigations, one of them by way of Cape Horn. The aft cabin lets the off-watch crew rest away from the cockpit.

Interior Layout & Living Aboard

The Hylas 44’s centre-cockpit layout is its greatest accommodation asset, creating a two-cabin, two-head arrangement with a separate aft stateroom — the reason, as Kretschmer puts it, that people choose centre cockpits despite their sailing compromises. The interior blends teak and mica, giving a warm wood feel without being a “cave”, and he rates the joinerwork as excellent. Dick Jachney, the US importer, told SAILING that in the early years each hull was assigned its own team of shipwrights who fashioned bulkheads, veneers and trim by hand. There is no moulded liner; bulkheads and furniture facings are tabbed to the hull.

Forward cabin: Bluewaterboats.org describes an offset berth and settee with a private head and shower; Kretschmer notes that the forward cabin came with either an offset double or a V-berth, and that the forward head is to port. It serves as a guest cabin with its own head.

Main salon: An L-shaped settee or dinette to port with a straight settee opposite. Kretschmer cautions that the salon is not huge and that storage there is limited because water or fuel tanks sit under the settees. Ventilation from hatches and opening portlights is good.

Dual walk-throughs: This is the Hylas 44’s most distinctive feature, and Bluewaterboats.org calls it tremendously popular. Leading aft from the main salon to the master stateroom are twin passageways — the galley to starboard, and the navigation station with the aft head to port. The arrangement separates the public and private areas of the boat and lets the cook and navigator work independently.

Galley: Located to starboard in the walk-through. The double sinks sit under the cockpit on a console that also covers the engine, which Kretschmer calls a clever use of space that leaves room for huge refrigeration and freezer compartments opposite and plenty of counter space. The walk-through position lets the cook brace against both sides of the passage in a seaway.

Navigation station: Opposite the galley, with a good-sized chart table, room for instrument repeaters and a comfortable seat. Kretschmer singles out the electrical panel as impressive. This is a dedicated workspace, not a corner of the salon.

Aft cabin (master stateroom): The highlight of the Hylas 44’s interior. A centreline queen berth (on all hulls except the first thirteen, which had a berth offset to starboard), a head with shower, and an abundance of drawers, lockers and hanging space. The aft cabin is reached through either the galley or the aft head, which has two doors. The hull carries its maximum beam well aft, which Bluewaterboats.org credits for the width of this cabin. Kretschmer notes that neither head has a dedicated shower stall.

Liveaboard assessment: For a cruising couple, the two cabins, two heads, full galley and dedicated navigation station cover the needs of daily life afloat. Water tankage is quoted at 80–100 US gallons, adequate for coastal cruising but worth supplementing with a watermaker for extended offshore passages. The charter background left useful features: Kretschmer lists double alternators, extra plumbed pumps for the freshwater system, cockpit access to key electrical fittings and robust, easily reached tank manifolds, plus a huge lazarette astern. Cockpit stowage, by contrast, is limited.

Hylas 44 Ownership: What to Expect

Like any 30–40 year old yacht, a Hylas 44 needs a steady programme of upgrades and maintenance. The main recurring items are set out below.

  • Insurance: Offshore and hurricane-season coverage will push premiums up; obtain quotes for the intended cruising grounds before buying.
  • Marina or mooring: Fees vary widely by location; a mooring is usually cheaper than a slip where available.
  • Haul-out and bottom paint: An annual haul-out covers travel lift, pressure wash, antifouling, anode replacement, and hull inspection. As on any GRP boat of this age, check the hull for osmotic blistering.
  • Engine maintenance: Annual servicing covers oil, filters, impeller, belts, and coolant. However, the engine’s location in the Hylas 44 makes a repower a major undertaking — look for a boat with a low-hour engine if possible.
  • Rigging: Standing rigging should be replaced every 10–15 years. A full re-rig including wire stays, turnbuckles, and chainplate inspection is a significant job on a boat of this size. The masthead and spreader fittings of the keel-stepped mast should be inspected regularly.
  • Sails: Check the age and condition of the mainsail, genoa and, on cutter-rigged boats, the staysail.
  • General maintenance and upgrades: Spending depends on the boat’s condition and the owner’s standards. Common upgrades include modern electronics (chartplotter, radar, AIS), watermaker installation, solar panel and lithium battery conversion, LED lighting, and refrigeration improvements.

Condition varies widely after three or four decades and several owners. Some examples come to market already fitted out for cruising, with watermakers, solar panels, wind generators and long-range communications; a boat where someone else has already invested in the critical upgrades, and documented them, is worth seeking out.

How to Buy a Hylas 44: What to Look For

The Hylas 44 was built from 1984 to 1992 on Queen Long’s timeline, and there is variation between early and late boats. The first thirteen hulls have an offset aft berth rather than the centreline queen, and Bluewaterboats.org notes that the earliest boats (1984–86) also have smaller cockpits. Late in production the 44 was given a swim platform and new deck mould as the Hylas 45.5, and some owners later retrofitted swim platforms to 44s; Bluewaterboats.org warns these aftermarket conversions often have their own issues. Many 44s also spent their early years in Caribbean bareboat charter under CYC’s purchase-and-charter scheme — high engine hours, eyebrows along the cabin trunk and a Hylas logo in the cockpit are the tell-tale signs. Understanding where a specific boat falls in the production sequence, and its charter history, is an important part of the buying process.

Key Configurations

Buyers will encounter several configuration variables. The keel is either a deep fin (6 ft 11 in draft) or a shoal bulb keel (about 5 ft 5 in draft) — the deep keel suits open-ocean sailing, the shoal keel island cruising and the ICW. The rig is either a masthead sloop or a cutter (with an inner forestay for a staysail). The engine is a Yanmar 4JH-TE (55 HP, fitted to most boats), the original Perkins 4-108 (50 HP), or, on a few boats, a Westerbeke 62. The forward cabin has either an offset double or a V-berth.

Known Issues to Inspect

  • Engine selection and condition: Identify which engine is fitted and have it surveyed. Kretschmer notes that most 44s for sale have very high engine hours and that engine access is not very good, so because the location makes a repower a big job, a low-hour engine is worth paying for.
  • Steering cables: Kretschmer names the push-pull steering cables as a more common problem than the ones buyers tend to worry about: they are prone to corrosion, and if they have not been changed before, show corrosion or the steering is stiff, replace them.
  • Leaks: He also describes the overhead hatches and portlights as notorious for leaking (an irritation rather than a serious problem; many owners have replaced hatches), and advises checking the hull-to-deck joint in the forward cabin for signs of leaks and the mast partners as a potential leak source.
  • Keel attachment: The lead ballast is mounted as a shoe on a fibreglass keel stub. As on any boat of this age, have the surveyor inspect the ballast fastenings and the keel-to-stub joint for any signs of weeping or movement.
  • Through-hull fittings and seacocks: All bronze through-hulls and seacocks on boats of this age must be inspected for dezincification and corrosion. Budget for replacement of any substandard fittings.
  • Deck core moisture: The balsa or Airex cored deck can absorb moisture over time if the sealant around deck hardware has failed. Moisture-metre readings should be taken across the entire deck during survey, with particular attention around chainplates, stanchion bases, cleats, and any deck-mounted hardware.
  • Standing rigging: Wire standing rigging has a typical lifespan of 10–15 years; Kretschmer says that if the original swage fittings are still on the boat it is definitely time for a re-rig. He also flags the 44’s internal chainplates as vulnerable to crevice corrosion. The keel-stepped mast should be inspected at the step for corrosion and proper drainage.
  • Rudder bearing and skeg: Have the rudder bearing, skeg and rudder stuffing box checked for wear and play during survey, as on any boat of this age.

Equipment That Adds Value

When assessing a used Hylas 44, look for the following additions: a low-hour engine, recently replaced standing rigging, new or recent cruising sails, modern electronics (chartplotter, radar, AIS), a watermaker, solar panels and/or wind generator, lithium battery bank with inverter, SSB radio or satellite communications, feathering propeller (Max-Prop or Variprop), dinghy davits, and a well-documented maintenance history. A Hylas 44 that has been set up for bluewater cruising by an experienced sailor — with these systems already installed, tested, and proven — is a different proposition from a bare or neglected example.

Commissioning a Survey

A survey of the Hylas 44 should include a full hull and structural inspection (out of water), moisture-metre readings across the entire hull and deck, a keel bolt assessment, rudder bearing inspection, rigging inspection by a qualified rigger, engine and systems survey, and a sea trial covering all points of sail. The surveyor should have experience with solid fibreglass construction and centre-cockpit designs. Given the variation in engine types and keel configurations, ensure the surveyor understands exactly which specifications the boat carries before the inspection begins.

Hylas 44 vs Competitors

The Hylas 44 competes with other bluewater-capable cruisers in the 42–45 ft range, each with a distinctive design philosophy, construction approach and loyal following.

Hylas 44 vs Hinckley Sou’wester 42

The Hinckley Sou’wester 42 is the American pedigree alternative. Designed by McCurdy & Rhodes and built by Hinckley Yachts in the United States from 1982 to 2006, it carries 9,000 lbs of ballast in a 23,500 lb displacement (Hinckley’s 2001 figures) — a 38.3% ballast ratio, so the Hinckley is heavier but less stiffly ballasted than the Hylas. The critical difference is layout: the Hinckley is an aft-cockpit masthead sloop with a single head, designed for a cruising couple; the Hylas is a centre-cockpit cruiser with two staterooms and two heads, designed for a couple who occasionally host guests. For the buyer who prioritises guest accommodation and a centre-cockpit layout, the Hylas wins. For the buyer who values Hinckley’s build and brand heritage, the Hinckley is the natural choice.

Hylas 44 vs Pacific Seacraft 44

The Pacific Seacraft 44 is the pure passagemaker in this comparison. Designed by Bill Crealock and built from 1990 in Fullerton, California (Washington, North Carolina, from 2008), the PSC 44 features a traditional canoe stern, cutter rig, fin keel and skeg-hung rudder — a conservative approach to offshore yacht design. At 27,500 lbs, the Pacific Seacraft is significantly heavier than the Hylas (22,320 lbs), creating a more ponderous but ultimately steadier motion in a seaway. The PSC’s beam of 12 ft 8 in is ten inches narrower than the Hylas’s 13 ft 6 in, resulting in less interior volume but a narrower hull. Both boats were offered with a shoal keel: the PSC’s draws 5 ft 3 in against a standard 6 ft 3 in. The key distinction is design philosophy: the Hylas is a modern Frers design that balances performance with comfort; the Pacific Seacraft is a traditional design that prioritises ultimate seaworthiness above all else.

Hylas 44 vs Tartan 4400

The Tartan 4400 represents the modern performance-cruiser alternative. Designed by Tim Jackett and built from 2002, the Tartan is a generation newer than the Hylas, with epoxy and Core-Cell construction. At 24,000 lbs with a beam of 14 ft 1 in (4.30 m), about 7 in wider than the Hylas, the Tartan carries 9,000 lbs of ballast for a 37.5% ballast ratio — significantly less than the Hylas’s 49.4%, though the Tartan carries its ballast in a bulb at the foot of its fin. The SA/D ratio of 18.2 versus the Hylas’s 17.6 indicates slightly more sail area for its weight. The critical difference is age and pedigree: the Hylas is a 1980s bluewater design with a record that includes circumnavigations; the Tartan is a modern performance cruiser. For the buyer who wants modern performance, technology, and amenities, the Tartan is compelling. For the buyer who wants proven bluewater pedigree, the Hylas is the choice.

For a full interactive comparison between the Hylas 44 and competing models, visit the Hulls.io Market Intelligence tool.

Written by the Hulls.io editorial teamUpdated May 2026

Frequently Asked Questions

Is the Hylas 44 a good bluewater cruiser?
Yes — the Hylas 44 has a strong bluewater record. According to John Kretschmer, a former Hylas delivery skipper writing in SAILING, several Hylas 44s have completed circumnavigations, including one known passage around Cape Horn. German Frers drew a fine-entried hull with a 49.4% ballast ratio — nearly half the boat's 22,320 lb displacement is in the external lead ballast. The solid hand-laid fibreglass hull from Queen Long Marine is reinforced with full-length stringers and transverse floors. The centre-cockpit layout and dual walk-throughs give the off-watch crew a separate aft cabin during passages. Published tankage varies: fuel is quoted at 80–100 US gallons (Bluewaterboats.org) or 110 gallons (Kretschmer), and water at 80–100 US gallons; many bluewater owners add a watermaker.
What engine does the Hylas 44 have?
According to Kretschmer, the original engine was the Perkins 4-108 (50 HP), a few boats had Westerbeke 62s, and most came with the Yanmar 4JH-TE, a 55 HP turbocharged four-cylinder diesel he describes as a very good engine that will run a long time. He notes that most boats for sale have very high engine hours and that engine access is not very good; because the engine's location makes a repower a big job, a low-hour engine is worth looking for. Whichever engine is fitted, have it surveyed.
What are the known problems with the Hylas 44?
Kretschmer, writing in SAILING, names the push-pull steering cables (prone to corrosion — replace them if they have not been changed, show corrosion or the steering is stiff) and leaks as the more common problems: the overhead hatches and portlights are notorious for leaking, and the hull-to-deck joint in the forward cabin and the mast partners are worth checking. He also flags the internal chainplates as vulnerable to crevice corrosion and says a boat still on its original swage fittings needs a re-rig. Bluewaterboats.org notes that many 44s spent years in Caribbean bareboat charter and that aftermarket swim-platform conversions often have their own issues. Beyond that, survey as for any boat of this age: ballast fastenings and the keel-to-stub joint, deck core moisture around hardware, through-hulls and seacocks, and the rudder bearing. The boat is also wet on deck because of its fine bow and low freeboard — a design characteristic rather than a defect.
How does the Hylas 44 sail?
Kretschmer, who logged around 20,000 bluewater miles in Hylas 44s, describes the boat as close-winded for a cruising boat: it tracks well, does not pound upwind even in sloppy seas and does not make excessive leeway. The 864 sq ft of sail area and SA/D ratio of 17.6 put it in the range sailboatdata.com describes as reasonably good performance. Downwind it handles large following seas with ease — he recalls surfing at double-digit speeds — and he rejects the claim that it is squirrelly. It is stiff, though it heels a bit, and heaves-to efficiently in heavy weather. In light air the SA/D of 17.6 is adequate rather than generous, so a Code 0 or large genoa helps. The trade-off is a wet ride due to the fine entry and low freeboard.
Hylas 44 vs Hinckley Sou'wester 42 — which should I buy?
These boats serve different needs. The Hylas 44 is a centre-cockpit cruiser with two cabins, two heads, and a true aft cabin — suited to a couple who want guest privacy and bluewater capability. The Hinckley Sou'wester 42, designed by McCurdy & Rhodes and built by Hinckley from 1982 to 2006, is a masthead sloop with a single head. The Hylas has a higher ballast ratio (49.4% vs 38.3% on Hinckley's 2001 figures). Choose the Hylas for accommodation and offshore capability; choose the Hinckley for its build, heritage, and the Hinckley ownership experience.
What is the difference between the deep and shoal keel Hylas 44?
The Hylas 44 was offered with two keel configurations. The deep fin keel draws 6 ft 11 in (2.10 m) on sailboatdata.com's figure (Bluewaterboats.org lists 6 ft 6 in) and is the better choice for open-ocean sailing and windward work. The shoal bulb keel draws about 5 ft 5 in (1.65 m) and opens up the Bahamas, the Intracoastal Waterway, Chesapeake Bay and other shallow-water cruising grounds that the deep keel cannot reach. The right choice depends on intended cruising grounds, so confirm which keel a prospective boat carries.
How many Hylas 44s were built?
The exact total production number is not publicly documented. Queen Long Marine's own timeline dates the Hylas 44 to 1984–92; SAILING magazine, citing the owners' association, gives US availability from 1985 and production until 1993, when a swim-step transom turned the same hull into the Hylas 45.5. Variations across the run include sloop and cutter rigs, deep and shoal keels, Perkins, Yanmar and Westerbeke engines, an offset double or V-berth forward, and an aft cabin berth change from offset to starboard (the first thirteen hulls) to centreline queen. The Hylas 46, a fresh German Frers design, followed in the mid-1990s (1995 on Queen Long's timeline) and replaced the 44 and 45.5.
What is the interior layout of the Hylas 44?
The Hylas 44's centre-cockpit layout creates a two-cabin, two-head arrangement with a separate aft stateroom. Forward, an offset double or V-berth with its own head to port. The main salon has an L-shaped settee or dinette to port and a straight settee to starboard; storage there is limited because tanks sit under the settees. The distinctive dual walk-throughs lead aft — galley to starboard, navigation station and aft head to port, with the engine under the galley console. The aft master stateroom has a centreline queen berth (on all hulls after the first thirteen), a head with shower, and generous drawers, lockers and hanging space; Kretschmer notes neither head has a dedicated shower stall. The interior blends teak and mica, and he rates the joinerwork as excellent.
Is the Hylas 44 good for living aboard?
Yes — the Hylas 44 is a good liveaboard platform for a cruising couple, thanks largely to the centre-cockpit layout. The aft cabin with centreline queen berth (after the first thirteen hulls) and its own head gives genuine owner's accommodation, and the forward cabin serves as a guest cabin with its own head. The galley has double sinks, large refrigeration and freezer compartments and good counter space, and the navigation station is a dedicated workspace. Water tankage is quoted at 80–100 US gallons, adequate for coastal cruising, but most liveaboard owners add a watermaker for extended cruising independence. The salon is not huge and its storage is limited by the tanks under the settees, but there is a large lazarette astern.
Share this guide

Browse by Category